Admin

,,,tray made from expanded polystyrene...

Well, I thought it was appropriate to make an improvement on my older antenna project, which is why I made this optimization...

From the history of the issue with the patch. We LTE800 turned on earlier than the other ranges. Frequency 2600 was busy mmds TV. Now there is a gradual replacement for LTE800 LTE1800 or LTE2600. Therefore, these antennas released. In the photo panel mimo LTE800. Cover moisture resistant PVC does not warp and does not limp.

,,,it"s good...!!!

,,,try to check this tokens at simulator cst ...!!!

", it does not matter the diameter of the PVC cylinder, you give it a screw hole...

,,,best. instead of Teflon spacers. uses metal spacers,,,

", delete all the results and get it from the beginning...!!!

I think so,,,

,,,stuck means that CST Progess has been blocked....?? ,,,or stuck means " sticking "....??

...wow, can you give some size ... ??? ok, but tell me though, why only 13 dBi ...?

,,,why,use google translate...and copy paste....!!!

,,,,but what, you are hard to open a new topic with your antenna ... ??

Dude,thanks...!!!

,,,okay,I just try it ...!!!!

,,,good, where did you get that ... ??? ,,,transmits vibrators and directors separately...!!!!

This is ok too...!!!

Broadband antenna 2G/3G/4G/WIFI. Gain 20 dB. Supports standards LTE1800, GSM1800, UMTS2100, WiFi2400, LTE2600. It is recommended to use complete with 3G/4G modems and GSM1800/3G repeaters. Panel antenna KP20-1700/2700 is designed for use with 3G, 4G, YOTA modems, GSM/3G repeaters in the range of 1700-2700 MHz. The antenna is compatible with the equipment to the following standards: 2G(EDGE, GPRS frequencies GSM1800) 3G (UMTS 2100) 4G (LTE1800, LTE2600) 2.4 GHz WI-FI (IEEE 802.11 b, g, n) A wide range of operating frequencies of the antenna enables 3G/4G modems to work effectively at the boundaries of the service areas 4G. The modem will automatically switch to the 3G standard, in the absence of a 4G signal, and the antenna will provide a high-quality signal in both bands. The body of the antenna is made of ABS plastic resistant to UV radiation and precipitation. The antenna input has short circuit DC current between the outer and inner conductors, which reduces the probability of accumulation of static electricity at the input of active equipment, reducing the probability of failure from static electricity, and makes optional the use of gazorazryadnoi. Antenna mount designed for installation on a vertical pipe with a diameter of 32-40 mm. and allows you to adjust tilt. Dimensions (length , width , height ), mm 445 x 445 x 80 Antenna - features : Operating frequency range, MHz 1700-2700 Antenna gain, dB 20 SWR in the frequency range, not more 1.7 Polarization Vertical Input impedance, Ohm 50 Maximum input power, watts 10 Connector F - female N - female Permissible wind load, m/s 30 The operating temperature range, oC -40 ... +50 The maximum permissible humidity of air, % 100 Crosspolarization isolation is not less than, dB 0 Connection standard 4G(LTE2600), YOTA LTE 1800 WiFi 2400 GSM 1800 Multi-band 3G (UMTS2100) Mounting type on the tube Execution type directed A very good movie on the subject, the author Maxim Dakhin (firm Crocs)...

,,,you put what you want, preferably copper sheet or galvanized sheet...!!!!

No, it must to be checked...!!!

my junkies... This is very good ... I think ... for offset parabolic...