lrg

Да, из этого видео Yes, from this video

It is clear you used computer racks on which the motherboard is installed.

Подскажите толщину стоек. Я нашлол от приборов.чтобы меньше их переделывать. Нет поблизости токаря. Tell me the thickness of the racks. I found it from devices. To reduce them less. There is no nearby turner. Tell me the thickness of the racks. I have these.they probably will be able to come up with some small alterations.there's no lathe in the vicinity.:-)

Chilanzar? Where can I find it?

so says the developer https://kroks.ru/shop/antenny-gsm-3g-4g-wifi/panel-antenna-3g-18-db-kp18-2050-modem/

What is the thickness of the metal used in this feed?

Sorry I hurried and did not even ask about the thickness of the metal patches in this irradiator

I can't. I don't have this antenna.

Kroks AP-221M1-Pot - is router with 4G mPCI modem and the 9 dB antenna built into a housing designed for installation on the street. Advantages over traditional solutions: The device already contains 4 components, which is usually purchased separately: antenna, microwave path from the antenna to the modem and the router. mPCI modem allows you to get the maximum possible speed 4G Internet that may not always provide a normal USB modem Due to the fact that the antenna and modem installed as close as possible to each other, the loss of the microwave cable is minimized. Easy to install. For mounting the device it is necessary to lay only one cable is twisted pair, which is much easier, faster, and cheaper, than to lay two microwave coaxial cable. To power the router does not need to mount a separate cable, as the power is on twisted pair. The power injector is already included in the delivery set of the device. Inside the device is mini-PCI modem Huawei ME909s-120. The router has one LAN port is 100 Mbps. Key benefits: compact size supply voltage 9 to 24 Volts Operating frequencies: 2G - EDGE/GPRS/GSM 1900/1800/900/850 MHz 3G DC-HSPA+/HSPA+/HSPA/WCDMA B1/B2/B5/B8 4G - LTE (FDD) B1/B2/B3/B5/B7/B8/B20 Data transfer rate: 4G - up to 100 Mbit/sec (input) / 50 Mbps (Exodus) 3G - up to 43.2 Mbps / 5.76 Mbps (Exodus) Ports and interfaces: Ports Ethernet, 1 PC, 100 Mbit/s SIM reader Main features: 128 MB Ram Rom 32 MB The power of the transmitter modem +23 ... +33 dBm CPU 600 Mhz Power 9~24 V, not more than 10 watts.

Yes

what's your distance to the base station? in my opinion, the worst option would be an irradiator and a working mirror.

Thank you so much. it's an important frequency for me.I have already started manufacturing : -) .in General, it would be interesting to know the size of the irradiator at 2.6 MHz

In this topic of course same on 2600 MHz . and it would be very smart for two frequencies of 2600 and 1800 MHz.under the 75 Ohm cable

Thanks. I will be grateful for the exact dimensions of the irradiator. I would like to try it at work.

I want to make this irradiator in iron. Can the size of this radiator. Thanks

it would be very chic to transfer it to 75 Ohm cable

For those who have hand sharpened correctly, sgser(c site Lan23.RU) and manufacturer-SPE Anteks represent the simplified version MMO feed 1900-2200 MHz, I remind you that the development is protected by patent RU117484. Drawings pulled from the HFSS file our forumchanin Over146%, for which separate him thanks. The first drawing-material thickness 1 mm, II 0.5 mm. For those who do not need the MIMO mode, it is possible to make only one port, any leave (with a strip of the features better, but to make it hard) This radiator has never been done in hardware, someone has a chance to become the first. Good luck!

why not advise?

this is a feed for offset parabolic antenna