Аntenna Аntex Vika-24F MIMO

[lrg 30]

Antenna Anteks Vika-24F MIMO

General information

Panel antenna Vika-24F MIMO is intended for use in complete equipment of wireless data transmission systems standards:

4G (LTE1800, LTE2600) 3G (UMTS 2100) 2G (GSM1800) WI-FI (IEEE 802.11 b, g, n)

Electrical characteristics

Operating frequency range, MHz 1700÷2700

Gain, dBi 2 x 21÷24

Width days, hail 8÷14

The sidelobe level, dB <-18

The ratio of forward/reverse, dB>20

Input impedance, Ohm 75

The CWS in the range of 3G/4G/WIFI, not more than 1.9

Isolation between ports, dB, More than 25÷30

Power handling, watts 10

Polarization Vertical + horizontal X-pol

Mechanical antenna characteristics

Weight with mount, g

Overall dimensions, mm 800 x 800 x 540

Connectors 2 x F-female

Antenna material Galvanized steel, aluminum

The protective box material ABS+polycarbonate

Operating temperature range -40 .... +60°C

Standards support ?????GSM900(2G), GSM1800(2G), UMTS900(3G), UMTS2100(3G), LTE800(4G), LTE850(4G), LTE1800(4G), LTE2600(4G)

Type ispolnennaya parabolic

Operating frequency range 1700 — 2700 MHz

Gain 24dB

Gain range,21-24 dB

Connectors for ??????F-female

Operating temperature range -40 .... +60°C

Material galvanized sheet, steel, aluminum

Material of protective polycarbonate

Dimensions (length, width, height) 800 × 800 × 540 mm

Weight 4760 g

Equipment Antenna Vika-MIMO 24 in the exploded view, the attachment point on the mast, installation instructions, packaging (carton+polyethylene)

Manufacturer Antex

[Admin 2545]

,,, it would be interesting to see the adaptation of this antenna to the 75 Ohm cable...!!!

 I believe that  the crossed-dipole, is built on double plated PCB

[lrg 30]

 

[lrg 30]

 

[Admin 2545]

,,,and this it"s UMO-3F MIMO2x2 for offset parabola...???

Just added a protective solder mask..

 

,,,and on YouTube...

 

[Sl4va 11]

On 14.11.2019 at 9:57 AM, Admin said:

,,,and this it"s UMO-3F MIMO2x2 for offset parabola...???

and there are her drawings? 

I think it's not difficult to make such an etching?

 

 

 

 

[clanon 246]

Isolation for DIPOLES at 90 degrees should be high...(because of the radiation diagram)

Baluns seem complicated without a BETTER picture

FR4 losses are HIGH...

it should be possible to make it in METAL over PES FOAM(low density)...HIGHER EFFICIENCY

Edited July 20, 2020 by clanon

[Admin 2545]

That's what the vibrator looks like...

 

[Admin 2545]

Vika-1.1-800/2700N MIMO-Mesh Collapsible Parabolic Broadband Antenna LTE800/LTE900/LTE1800 / UMTS2100/LTE2100/LTE2300/LTE2600

Powerful 2G/3G/4G/WIFI broadband antenna with high wind resistance and collapsible design. Gain 15-26 dBi. F=790-960/1700-2700 MHz. Ra=50 ohms. Recommended for use with 3G/4G modems and routers over long distances.