Looking for both a small panel antenna and disk yagi antenna design for 3g 1900mhz band

[calipso99 1]

as the title says, im looking for a simple panel antenna design that can be used as feed point for a off set oval vertically oriented dish. i only have RG6/U cable to connect the antenna to the device, which is a 3g dongle.

also looking for a Disk yagi antenna design for the same pùrpose, 3G 1900mhz band.

[Admin 2545]

,, welcome, but on this site you did not find anything useful to you...!!!???

[calipso99 1]

1 minute ago, Admin said:

,, welcome, but on this site you did not find anything useful to you...!!!???

go to this YT video and go to 11:52

 is that good design for 1900mhz 3G band ? (1850mhz-1989mhz)

Regarding the patch antenna design, havent found a simpler enough design for a dish feed point.

[Admin 2545]

,,, for offset dish, I think this is better...

[calipso99 1]

4 minutes ago, Admin said:

,,, for offset dish, I think this is better...

like that design, looks not too hard to make, is that an active element plus a parasitic ?

[calipso99 1]

15 minutes ago, Admin said:

,,, for offset dish, I think this is better...

forgot to mention, the dish measures 60x66cm, the widest size is on the vertical axis, just a regular satellite tv dish

 

[calipso99 1]

Regarding the disk yagi antenna, that will be a standalone.. just another option. the celullar towers are not farther than 3km, im withing coverage but ping is bad. i dont have line of sight, just trees in the way.

Edited October 30, 2021 by calipso99
adding to my comment

[Admin 2545]

,,, the distance is not great and the trees do not have such a great influence ....!!!

[calipso99 1]

3 minutes ago, Admin said:

,,, the distance is not great and the trees do not have such a great influence ....!!!

good to know, so you have the dimensions of the panel antenna you shared with me ?

[clanon 246]

Is it MiMo the dongle...? Two antennas...

[calipso99 1]

Just now, clanon said:

Is it MiMo the dongle...? Two antennas...

its a huawei E1756 , it has a single U.FL (or at least it looks like it) port for a external antenna. and im worrying a bit about how im going to connect my antenna to the dongle. thinking about desoldering the U.FL port and soldering some small diameter coax straight to the board.

[Admin 2545]

,,, for MiMo, you need another type of antenna...!!!

,,, aaa, well if you have huawei E1756 modem ... why don't you put him in the focus of offset  dish??

[calipso99 1]

10 minutes ago, Admin said:

,,, for MiMo, you need another type of antenna...!!!

,,, aaa, well if you have huawei E1756 modem ... why don't you put him in the focus of offset  dish??

im quite far from the dish, some 8 meters of cable lenght needed, dont think it would be wise to have a USB cable that long, plus i want an actual antenna for my dongle.

Hope you can share the dimensions of the panel antenna.

[calipso99 1]

1 hour ago, Admin said:

,,, for MiMo, you need another type of antenna...!!!

,,, aaa, well if you have huawei E1756 modem ... why don't you put him in the focus of offset  dish??

Could you at least recommend me a good antenna designer program? one that can design a panel type antenna

[Admin 2545]

,,, maybe tomorrow I will give you the details of this antenna...

[calipso99 1]

Alright

[Admin 2545]

,, try to open your huawei E1756 modem to see where the inside antenna is...!!!

[calipso99 1]

2 hours ago, Admin said:

,, try to open your huawei E1756 modem to see where the inside antenna is...!!!

already did, its between the usb port and the rest of the dongle. right next to it is a U.FL female connector. i got to say, cant find the copper trail that connects to the internal antenna.

[calipso99 1]

 

 

 

I would feel more comfortable soldering the antenna wire there where the U.FL connector goes. i would need to desolder that connector first and then solder some thin coax wire straight to the board.

[calipso99 1]

oh by the way, the cell tower i want to reach is actually 5.5km away. no ground obstructions.. just trees.

[Admin 2545]

[Admin 2545]

,,, these are the promised dimensions ... !!!

[calipso99 1]

Thanks a lot, the dimensions are in Milimeters? also, thats a 45 degree bend on each side of reflector ?

[calipso99 1]

https://media.istockphoto.com/photos/polystyrene-foam-picture-id178579873 also, you mean polysterene foam as dielectric ?

[Admin 2545]

,,, yes, the foam is dielectric and the dimensions are in millimeters...!!!